Hyperion 900x250
Log In
Access Premium Site»
Not a member? Join today!

RPM Landing Gear For The Dromida Vista, Ominus And Ominus FPV

RPM Landing Gear For The Dromida Vista, Ominus And Ominus FPV

From RPM:

The Dromida Vista and Ominus are geared towards the entry-level flyer so there’s a need for more cushion in the landing system. The stock motor cover with the small rubber foot, doesn’t have enough cushioning effect to save a harsh landing and adds the possibility of damaging the motor or gear system if the cover breaks or shifts during a crash. The stock motor cover is somewhat short as well, leaving the possibility of a blade strike in tall grass a distinct possibility.

RPM Landing Gear for the Dromida Vista and Ominus solves both of these issues and many more. Our versions replace the motor cover and rubber foot with a solidly mounted, curved “spring” made from our engineering grade, ultra-lightweight nylons. The curved “spring” adds impact-absorption to the airframe, helping to reduce or eliminate damage from those questionable landings. Our Landing Gear also elevates these quads by an additional 0.63” (16mm) on the Ominus, 0.26” (6.5mm) on the Ominus FPV and 0.55” (14mm) on the Vista and Vista FPV, reducing the probability of a blade strike in grass or during bad landings.

RPM Landing gear also spreads the center point of each leg further out by 0.36” (9mm) on each leg, adding much needed stability to take-offs and landings. We also curved the ends upwards making them less likely to catch or hook when one leg is grounded and the other three airborne.

Our last challenge was to keep the landing gear lightweight. For the ground clearance increase, stability and added crash protection gained with RPM Landing Gear, the entire set-up adds as little as 2.4 grams* to the total weight of the quad, causing minimal to no performance effects to overall battery life or flight characteristics.

RPM Landing Gear is sold is sets of 4 Landing Gear per package. Please review our website FAQ page for proper methods of dyeing white versions to any color of the rainbow!

Tech Notes: RPM Landing Gear is sold in sets of four and replaces Dromida #DIDE1126, #DIDE1164, #DIDE1180 & DIDE1220. A Phillips head or “crosshead” screwdriver with a maximum shaft diameter of 1/8” (3.1mm) is needed to install the Landing Gear. RPM aerial products are backed by our limited lifetime warranty against materials and workmanship issues but do not carry the same breakage warranty as our surface products. For more information on the RPM warranty policy as it applies to aerial products, please visit our warranty FAQ page on our website.

* Actual weight gain or loss varies by quad. Weight variation takes into account the weight loss by removing the original motor cover, rubber foot and any additional screws (Vista FPV) then adding the RPM Landing Gear weight.

#72111 – Dromida Vista, Ominus & Ominus FPV Landing Gear – Dyeable White – $8.95 / set of 4
#72112 – Dromida Vista, Ominus & Ominus FPV Landing Gear – Black – $8.95 / set of 4

RPM Landing Gear For The Dromida Vista, Ominus And Ominus FPV (4) RPM Landing Gear For The Dromida Vista, Ominus And Ominus FPV (1) RPM Landing Gear For The Dromida Vista, Ominus And Ominus FPV (2) RPM Landing Gear For The Dromida Vista, Ominus And Ominus FPV (3)

Updated: March 8, 2016 — 3:19 PM
Hobbico HR Challenge V2 600x120
WW II First Dogfights

Leave a Reply

Your email address will not be published. Required fields are marked *

Airage Media © 2017
For all Licensing, Permissions, Awards and Reprint requests please contact our official partner Wright's Media for more information. Please note that Wright's Media is the only authorized company that we’ve partnered with for materials and assets. Wright's Media contact: airage@wrightsmedia.com or (877) 652-5295.
WordPress Lightbox Plugin