FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS

FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS
Flying at several RC events I noticed that several pilots were struggling with or lost control of their models during simple turns. As one who diagnoses pilots’ flying skills for a living, it was obvious to me that the problem wasn’t that they needed more practice, but that they lacked an understanding of basic flight control.
Hangar Membership - Membership | FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS
Hangar Membership - Membership | FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS

If you’ve ever watched a proficient pilot fly (you can often tell by their mirror image perfect landings), you may have noticed how their general flying appears casually routine. In other words, they make it look easy. That’s because their control of the airplane has become mostly automatic. For example, instead of reacting to the airplane every time they perform a turn, proficient pilots simply repeat the same turn control inputs and the airplane predictably and consistently follows along. By focusing on controlling the airplane and repeating the same control inputs, you too can experience the same predictable results as pro fliers, and therefore experience greater proficiency in wind, easier transitions into new and different aircraft types, and more consistent landing approaches.

PROCEDURE (AILERON) TURNS

The procedure that pro pilots use to turn most aileron equipped airplanes starts by “setting the bank” with a smooth, yet brief, aileron input. Note that the aileron input is neutralized to avoid needless adjustments or entering a downward spiral, and then up-elevator is applied to pull the nose into a turn and to keep the turn level. The turn is then kept level mainly by adjusting the elevator versus “fiddling” with the ailerons as so many pilots mistakenly do.

The size of the aileron input determines the degree of bank and therefore the size of the turn, as well as how much elevator will be needed to keep the turn level. For example, a smaller aileron input produces a shallower bank and therefore a wider turn, whereas a larger aileron input produces a steeper bank and a tighter turn. The initial objective of every proficient pilot is to find the aileron input that consistently produces the degree of bank that we are comfortable with, and then determine the correct amount of elevator to pull each time to keep the turn level. You can anticipate that during a mild bank, most of the wing’s lift is still opposing the pull of gravity, and thus very little up-elevator will be needed to keep the turn level. During a steeper bank, there’s less upward component of lift to oppose gravity, thus more up-elevator is required to keep the turn level.

CONSISTENT TURNS

The neutral stick position provides a distinct point from which to gauge the size of each of our control inputs, therefore making correct amounts easier to repeat and incorrect amounts easier to modify correctly. For example, if your turns are too tight, rather than “fiddling” with the ailerons throughout your turns, simply reduce the size of your initial aileron input from neutral to produce a shallower bank and wider turns. Or, if you initially pull too much elevator and execute a climbing turn, repeat the same aileron input next time, but pull less elevator from neutral and the turn will be more level.

Hangar Membership - Membership | FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS
Hangar Membership - Membership | FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS

Performing a procedure turn can be summed up by the motto “Trust, then adjust.” That is, proactively initiate your turns trusting your inputs, then adjust (fine-tune) the amount of elevator you’re holding depending on what you see to keep the turn level. If you see the plane start to lose altitude during the turn, pull more elevator. If the plane starts to climb, lessen the amount of elevator that you’re holding in throughout the remainder of the turn. Keep in mind that as a rule, it is easier to add more input than it is to recover after over-controlling. Therefore, the best procedure is to target a small amount of elevator at the start of a turn, and then fine-tune the elevator, if necessary, to maintain a perfectly level turn.

RESTARTING & TIGHTENING TURNS

In the event that a turn needs to be tightened or restarted, the correct procedure is to smoothly apply an individual small bump of aileron (in-out) in the direction of the turn to steepen the bank angle while continuing to hold in the elevator. Remember, to avoid over-controlling, the aileron bump needs to be briefly applied in-and-out, not held in!

PROCEDURE TURN CORRECTION

Hangar Membership - Membership | FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS

At the point that you want to exit the turn, neutralize the elevator and smoothly apply opposite aileron to level the wings. Note that the key to applying the aileron in the proper direction is reminding yourself which way you’re turning and anticipating opposite aileron before it’s time to correct. The temptation to look at the wings to determine which way to apply the aileron produces hesitation and confusion whenever the position of the wings is not clear. Ultimately, correctly applying the aileron will hinge on how well you start and maintain level turns, because the less demanding the turn is in general, the easier it will be to remember which way to apply the aileron to level the wings. In fact, as long as the turn was kept level, you can actually get away with correcting the wrong direction, catch the mistake, and level the wings correctly with only minimal altitude loss. On the other hand, it can spell doom for an airplane if the pilot corrects the wrong way during a diving turn! Thus, prioritizing elevator adjustments to keep each turn level should be the top priority for most pilots.

RUDDER TURNS

Hangar Membership - Membership | FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS
Hangar Membership - Membership | FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS

A rudder turn is performed using the rudder to yaw the nose of the airplane in the direction that you want to turn, and while space does not permit going into all the details, most airplanes will also inherently bank in the direction that the rudder is applied.

There are basically two different techniques required to turn an airplane without ailerons using the rudder. Planes that exhibit a lot of upright stability, such as a high wing powered glider, typically resist banking and therefore requires you to continue holding in rudder to keep turning. These aircraft typically require a larger rudder input to get the turn started, but once started, the rudder has to be reduced to keep the turn from becoming too tight. Note: The inherent skid and subsequent speed loss when applying rudder will most likely require you to combine some up elevator with the rudder at the start of the turn to keep it from dropping.

Hangar Membership - Membership | FLIGHT TECHNIQUE — PRO PILOT TECHNIQUES FOR SMOOTH TURNS

KEEP IN MIND THAT RUDDER BANKS ARE LESS PRECISE THAN AILERON BANKS AND WILL TEND TO LAG BEHIND YOUR INPUTS IF APPLIED TOO QUICKLY

Other rudder planes require a technique similar to an aileron turn, where the rudder is applied only long enough to bank the wings, and then it is neutralized to avoid over-banking and entering a downward spiral. Similar to an aileron turn, the degree of bank and the size of the turn are dictated by the size of the rudder control input. Keep in mind that rudder banks are less precise than aileron banks and will tend to lag behind your inputs if applied too quickly. Thus, to achieve results that more closely match your intentions, you must apply all your rudder inputs very smoothly to give the plane a chance to keep up with your inputs.

Once the turn is started, you’ll need to adjust the elevator to keep the turn level, then level the wings with opposite rudder to exit the turn. Returning the wings to level usually takes longer with rudder than it does with aileron, thus you’ll have to start leveling the wings prior to the point that you want the turn to stop, and then continue holding in the rudder until the wings are level. Note that prolonged rudder defections and the resulting skids tend to scrub off airspeed, thus you will most likely need to hold in a little up-elevator while leveling the wings to keep the plane from dropping.

CONCLUSION

Proficient pilots don’t endeavor to get better at making corrections. Proficient pilots apply control inputs that reduce the need for corrections altogether. The key, therefore, is for you to pay attention to making consistent control inputs, and then if you don’t like the result, look to proactively change your inputs/commands rather than react to deviations. Consider that when your turn inputs are made correctly, the need for additional corrections may not even exist, and that is when you will be free to think ahead of the airplane just like a pro. Good luck and happy flying.

BY DAVID SCOTT, 1ST U.S. R/C FLIGHT SCHOOL

Updated: February 21, 2023 — 11:18 AM

2 Comments

  1. Great write up! Also worth mentioning the value of a coordinated turn vs slip, vs skid, and the value of adding enough rudder to maintain coordinated flight even in an aileron turn, especially in a cub type aircraft. I see pilots dragging the tail nose high through the turn way to often, keep the nose from pointing at the sky in your turns with the rudder!

  2. What about using rudder to keep the tail from “slipping” during the turn?

Comments are closed.

Air Age Media ©
WordPress Lightbox