Internal Wire Hinging for Scale Surfaces

Internal Wire Hinging for Scale Surfaces

One of the more unique features found on giant scale RC airplanes, and on warbirds in particular, are the inset hinges that use long, thin pivot wires to secure the control surfaces in plane. For my current project, an 85 inch span Douglas Skyraider, this type of hinging is used with the rudder, here are some pix and tips from my building board.

rudderA

Here you see the full-size rudder from a museum Skyraider. You can see that it has three inset hinge pivot points.

On the Bench

When it comes to building a control surface with inset or recessed hinging, you have to build very accurately and follow the plans precisely. I am building my Skyraider with laser cut parts from LaserCutUSA.com and they match the Nick Ziroli plans precisely.

photoE           Here are the rudder ribs, the sub-leading edge and the parts I used for the hinging. They are easy to obtain consisting of a length of 1/6-inch welding rod and the yellow inner section of a Gold-N-Rod pushrod from Sullivan Products. These are cut over size to begin with.

photoB

Cut the side sheeting to size and glue the sub-leading edge and the ribs to the right side as shown here. Notice I drew extension guide lines on the plans to help guide the placement of the ribs. Precision is the key to all properly build RC warbirds. I use ZAP CA glue for most of my building, but when it comes to gluing on sheeting for the rudder, I also use Titebond yellow  carpenter’s glue.

photoC

Here’s a close up of the lower end of the rudder. As you can see, the first hinge support is about an inch from the bottom and the hinge pin wire is secured to the bottom of the hinge. It travels in a straight line all the way to the top support.

photoA

Here’s the completed hinge assembly all glued together and sanded smooth. It fits the plans precisely in width and length. Note that I have drawn a centerline on the sub-leading edge.

photoG

Slide the wire into the yellow Gold-N-Rod and tack glue it over the centerline. Make sure to keep them straight and centered. I drew guide lines on either side of the yellow tube to ensure it is glued in the correct orientation. Next glue 1/8 inch filler strips on either side of the yellow tube and pivot wire, here the left filler piece has been glued in place.

photoHHere both filler strips have been glued in place, trimmed and sanded to shape flush with the outside surfaces of the rudder.

photoI This shows the three 1/8-inch plywood hinge support tabs that will secure the hinge to the fin and the lower rudder post of the fuselage. Mark the locations for the clearance slots that will be formed between the leading edge blocks that will be added next. The slots should be about 3/16 inch wide.

rud4

Using the plans as a guide, laminate the wood together to form the blocks. These should be slightly longer and wider than the final pieces so they can be planned and sanded to shape after gluing them in place.

rud3

Measure the distance between the hinge slots and sand the blocks ends square, cut to length, (slightly over size), and then sand the opposite end square until you have the exact length needed.

rud

Here you see the bottom end of the rudder with the leading edge blocks glued in place and rough shaped to size.

rud2

Here is one of the support tabs and the rudder. The space between the leading edge blocks forms the slot (or recess) for the hinge pivot point.

Next simply cut through the yellow guide tube with a Hobby razor saw, (remove the wire pin first), and clean out the pocket to fit the plywood support tab. Cut the slot down through the 1/8 inch filler strips.

sawphoto

saw-photo

I use a back-stroke saw from Sears. It is very sharp and cuts through balsa and the plastic tube easily.

pinphoto

Here you see the pivot wire reinstalled. All that’s left is to use your hobby knife to recess the slot near the center to clear the plywood support tab. A sharpened length of 3/16 inch brass tubing can be used, and then smooth everything out with some fine sandpaper.

rud1

This shows the finished installation of the rudder on the fuselage. Since my fuselage is not yet built, this example, (courtesy of Gains Smith), shows the setup. You use the completed rudder assembly and attachment tabs as a guide to glue the tabs in place on the fin and fuselage structure before they are sheeted over with balsa.

 

Updated: January 26, 2021 — 10:56 AM
Air Age Media ©
WordPress Lightbox