So, after getting the Skyraider up onto its landing gear last time out, I thought I would tackle finishing up the plug-in wing panels. This of course was started before the wings were sheeted by installing the hardware which included the aluminum wing tube and socket sets which are available from Nick Ziroli Plans.
Here the 1 inch diameter wing tube and the socket have been slide into place along with some of the alignment rings I made to center the tubes in the opening already cut into the ribs. The holes were cut for 1.25 inch tubes which would have been just too big for the reduced-size 85 inch span Skyraider.
Once the wing has been sheeted from the main spar back to the trailing edge, I used thick Zap CA and 15 minute Z-Poxy to securely glue the fixed end of the wing tube in place. Also the shear webbing has been glued in place.
Also, the rib-bay that will house the hard-point for the wing tip attachment screw is filled in with basswood as shown. I used a lead weight to hold the blocks in place as the epoxy cured. The weight also held then blocks in place so they would be flush with the bottom of the ribs so the sheeting when applied would fit smoothly over them.
Note that the bolt holes won’t be drilled into the wing panels and tubes until after the wing has been finished. This is because the ends of the wing panels will also be finished and sanded smooth. This would throw off the alignment if the holes were drilled now.
To help guide the future cuts that would separate the inboard and outboard wing panels, I made a few razor saw cuts between the two W10 ribs in the wing. I made short cuts at the trailing edges and at the leading edges before gluing the top sheeting into place.
I placed the Skyraider inverted on the maintenance stand and started the chopping on the bottom of the wing panels by drawing guide lines.
This is the scary part. I removed the blade from my razor saw and slowly and carefully cut into the wing at the trailing edge and the leading edge using the previous guide cuts for position.
Again I made the cuts slowly and carefully being sure to be in between the two W10 ribs. I stopped the cut just shy of the front and back alignment dowels already installed in the ribs. If I do this again, I will wait till after the wing panels are cut apart before gluing the alignment dowels in place.
I then used a flexible steel ruler and made cuts joining the leading and trailing edge cuts using a sharp X-Acto knife making several light cuts until I cut all the way through the sheeting and into the space between the two ribs. Here I am using the Razor saw blade to cut through the top and bottom main spars.
I continued to make razor saw cuts horizontally to completely separate the wing panels. Next I did the same thing in the top side of the wing.
In a few places some of the glued used to apply the sheeting had seeped in between the plywood ribs so I used thin-bladded APC electric propellers as wedges to help pry the panels apart.
There was a small pop as the wing panels finally separated cleanly apart. The whole process of doing it this way is to ensure that the ends of the two separated wing panels match each other perfectly.
I slowly pulled and wiggled the outer wing panel until the wing tube and the alignment dowels slipped out of the inner wing panel rib.
Ah! there it is, the wing tube slid cleanly and easily out of the socket tube.
There were a few small sections where the ribs had delaminated, but these were easily glued back together with thin Zap CA and sanded smooth.
Now all that has to be done now is repeat the whole process for the other wing panel. Pheww! This is a bit nerve racking but well worth the effort when it comes time to transport the Skyraider to and from the flying field.
The next task will be separating the ailerons and flaps from the wing and hinging them into place. Stay tuned!
For the next Post, CLICK HERE.
For the previous post, Click Here.
How do you lock the wing panels in place? Thank You.
i like it very much onhow its put together …im one that likes to build them still .
4-40 cap head screws go in from the underside of the wing into the outer wing tube/socket through the hardwood block. It is drilled and then tapped and then the screw is counter sunk so it is flush with the bottom of the wing. Same way as the original plan set.
excelente
Gerry, im starting the Ziroli Skyraider and have printed out your Build articles. I have all but cannot find #8,11,13 and am not sure if there is a 15, don’t know if i missed them or if they are tilted something else.
The articles are wonderful and i feel great about doing this project after reading them. I just finished a Proctor Nieuport 28C1 1/4 scale and think im ready for this.
Thanks for the wonderful articles on this and your help would be greatly appreciated in