Scale Detailing Secrets from a Top Gun Champion

Scale Detailing Secrets from a Top Gun Champion

In most modern jet models, the entire cockpit is very visible because of the large bubble canopies. When I started work on my first F-16 Thunderbird for Top Gun 2008, it was important to me to have outstanding cockpit detail. With the competition at such a high level of perfection, I decided to scratch-build everything I could as accurately as possible. My idea was to make everything as individual pieces. That meant every switch, knob, bezel and detailed part out of casting resin. By painting each part separately before assembly I could achieve the most realistic look possible. This required serious documentation, photographs and plans.

(Pictured above) The author Graeme Mears (right) and his pilot David Shulman show off Graeme’s award-winning Thunderbirds F-16 Falcon. Graeme earmed a perfect static score of 100 points at the 2009 Top Gun scale competition. A first!

I researched the Internet and found a German website (xflight.de), which had most of the information I needed. There were detailed general layout graphics, individual panels, as well as high-resolution pictures of all the instrument faces. I also required plans and pictures of the “Aces II” ejection seat. Again, surfing the net produced lots of information and the plans I needed I found in Verlinden Publications’ Locked On No. 2.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

All the little things add up to big-time realism. Here the seat back padding, harness and straps bring the ejector seat to life. They came from a BBI scale model pilot figure of the same scale size.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

Though it is possible to find scale parts and fittings from various commercially available sources, many times it’s necessary to scratch-build your own masters to form casting molds. Here you can see various parts that I had to machine and produce from raw materials so I could produce the required molds to resin cast the final pieces used to make up my F-16’s detailed cockpit. Plexiglas, G-10 fiberglass sheet material, brass and plastic are all used in the process.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

Molds and castings

To make molds, you first need an original part called the “plug.” Whenever I’m in department stores shopping for my grandchildren, I always look for any toys that have parts that can be used to make molds. You’d be surprised what you can find. Over the years, I’ve collected a lot of stuff like switches, map reading lights, joysticks, rudder pedals, knobs and a whole lot of other miscellaneous parts. For the F-16, however, there were still a lot more parts that I needed to make from scratch. I made them mostly from blocks or rods of Plexiglas using my milling machine and lathe. Some of the originals, like the parachute bags, I made using modeling clay.

Watertight boxes are required around the plug to retain the two-part silicone molding material. Once the material is mixed, it needs to be placed in a vacuum chamber, to eliminate any air bubbles before pouring it over the plug. I ended up with dozens of molds for the resin parts.

Casting all the required parts took a long time, as there were literally hundreds of them. I use a material called Por-A-Kast, which is a 50/50 mix. To produce a part free of bubbles and surface pin-holes, I used my vacuum/pressure pot to place the casting under pressure while it cured. The parts cure very quickly (in about five minutes), so you have to work fast. A well-thought-out procedure helps get a number of parts poured and into the pot before curing starts. The cured parts need to be left in the molds for about an hour to harden enough to be removed from the molds without breaking or distorting.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

To form silicone molds, you first have to make a box to hold the originals and then fill the box with the molding material.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

Left: Here is a one-piece mold I made for the control column hand grip. The mold is very flexible, so the cast part can be removed easily once it has set up.
Right: The finished molded part.

Control Panels & Nomenclature

To save weight and to provide a smooth surface for paint, the basic construction of the cockpit was constructed from a lamination of 0.010-inch G-10 fiberglass (franktiano. com) material applied to 1⁄8-inch balsa. All the control panels are layered like the full size and included all the mounting screws and correct nomenclature placards. The Xflite graphics were very valuable here. Using a combination of my CAD program, Design CAD3Dmax and Adobe Illustrator CS2, I reproduced graphics of all the information for every panel. This included all the knobs, switches, circuit breakers and nomenclature placement. I then printed the final graphic panels onto a white base water-slide decal material and applied them to 0.015-inch thick ABS plastic sheet material with the aid of a diluted solution of Formula 560 Pacer canopy glue to improve adhesion. Once the graphics were totally dry, I drilled the panels individually for switch and knob insertion.

After painting all the components, I glued them into their respective holes and then applied the finished panels to their trays with double-sided tape.

Now the laborious task of installing all the tiny screws that secured each panel could start. The screws I used (size 000-120) came from J.I. Morris Company and there was over 100 of them.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

Working in sections makes the job easier. In this photo, one of the completed side panels is now ready for installation in the cockpit tub.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

One piece added to another is how you make all the sub-assemblies. Here the main instrument panel begins to take shape.

Aces II Ejection Seat

The centerpiece of the cockpit is the ejection seat and it required several vacuum-formed and cast resin parts. I sized my 3-views drawings to the correct scale with my CAD program and used them as a guide to make all the required molds. There are a lot of pressed-aluminum parts in the full-scale seat, so I used vacuum-formed ABS to simulate these. Raised rivet details were applied using Formula 560 applied with a syringe.

The ejection rails are made from 0.040-inch G-10 material and scale-sized bolts (J.I. Morris Co., morris01550.com/minsc.htm), were added for scale effect. All the placards on the ejection seat were created in Illustrator and printed on water-slide decal material and applied after the pilot’s seat was painted.

Reproducing scale cockpit details is a rewarding experience. I hope the techniques outlined here will inspire you to try it for yourself. Going the extra mile while detailing a model’s cockpit will set it apart from all the rest, even if you are building a sport-scale model. Have fun.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

This is the “Before” shot of the cockpit tub waiting for the various sub assemblies to be added.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

Here’s the “After” shot showing the completed cockpit tub area. All that’s needed is for the ejection seat to be installed.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

The rear section of the seat is made from vacuum-formed sides and G10 fiberglass material. The rivets are brass pinheads. Once painted it will look like the part was made from sheet metal.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

The seat’s lower side is shown here with more rivet detail and vacuum-formed and resin cast parts added. Again the details are obvious.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

The top, rear portion of the ejector seat with the rails and the scale nuts and bolts is shown here. The green drag chute at the top is made of modeling clay. The overall appearance of the completed seat structure is well worth the effort—especially at the high levels of Top Gun scale competition.

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

The completed cockpit with detailed ejection seat in place. Notice all the fine rivet and bolt head details; even the placards and warning lables are there. [Editor’s note: the author’s efforts and attention to detail add up to an amazingly realistic cockpit treatment! Little wonder that Graeme is considered a master scale modeler.]

Text & photos by Graeme Mears

Model Airplane News - RC Airplane News | Scale Detailing Secrets from a Top Gun Champion

Updated: April 26, 2022 — 3:43 PM

2 Comments

  1. Amazing !

  2. Graemes Mears is in a class by himself. Humble in person, a pilot as well, he is the best of the best. I flew full scale fighters and marveled at his CNC landing gear workmanship, rivets, and hidden servo actuators. If Graeme builds your scale plane, you can be assured there will be none better.

Comments are closed.

Air Age Media ©
WordPress Lightbox