Workshop Build-Along — Sopwith Camel Part 9 — Cheek Fairings

Jul 21, 2014 1 Comment by

After a bit of break to cover the Warbirds over Delaware event, I got back in the shop for a little more quality Camel time. We left off with the aft turtle deck stringers being installed. From here forward at the top of the fuselage, the cockpit area and the machine gun “Hump” section is all one piece and makes up a removable hatch cover. This helps greatly with the access to the servos and fuel tank. Also, the sides of the fuselage from the cockpit forward has to transition from a square cross section to a round one to match the engine cowling. Here are some of the pix I took along the way.

IMG_0978

First step is to glue the top and two side formers to the front of the fuselage. When sheeted with 1/8 inch balsa. the diameter of the front of the fuselage will be perfect to match a Fiberglass Specialties’ 10 1/2 inch fiberglass radial cowl.

IMG_0979

Here the hatch base is taped in place between the aft cockpit former and the front top former. The two instrument panel formers are also glued in place.

IMG_0984

I used two formers here. they are identical except that the front one is cut to accept the back of the 1/4-scale Vickers machine guns from Williams Bros. I used 1/4 inch balsa fill to separate the two formers.

IMG_0987

Forward of the instrument panel formers is the main gun hump former. It is reinforced with 1/4 inch stick stock that will support the balsa sheeting covering this section of the fuselage.

IMG_0989

At the tangent point between the flat sides and the curved top corners, I added a 1/2-x1/4 inch reinforcement. This will strengthen the structure and give a gluing base for the sheeting. Flat sheeting is going to be used on the sides and top, while the rounder corners will be done with thinner strip planking.

IMG_1064

Before sheeting the gun hump area, I removed the hatch assembly and started working on the fuselage side cheek fairing sections. This starts with adding 1/4-inch strips to the top of the fuselage to act as gluing strips to support the side sheeting.

IMG_1065

The strip is then planed and sanded to blend from the fuselage side to the base of the top front former.

IMG_1080

Use the bottom wing’s root rib and position it in place with the help of the wing tube and socket and an alignment dowel . Trace the rib as a guide for former and sheeting placement.

IMG_1066

The second side former is then glued in place so it is just in front of the wing’s Leading edge.

IMG_1081

Glue the third side former in place then cut notches in the formers for the side stringer. The end of the stringer is cut to a taper so it can be glued to the fuselage side as shown here.

IMG_1068

Cut the filler block to shape and glue it between the bottoms of the second and third formers.

IMG_1083

Use a razor plane to shape it so it blends into the formers and then sand it smooth.

IMG_1072

Now add the bottom forward and aft filler strips and sand to shape. These will support the bottom edge of the side cheek sheeting.

IMG_1082

So here’s a trick my father taught me. Before gluing the first piece of sheeting over the formers, glue these tabs in place. They will help guide support the second sheet when it is glued in place so it is very even with the first sheet.

IMG_1085

Here the first piece of sheeting has been glued in place. It’s top edge over hangs the top of the fuselage slightly so it can be sanded flush with the base for the hatch cover.

IMG_1077

IMG_1078

Here the second piece of sheeting has been glued into place. Note there is no gap between the two pieces of sheeting and very little sanding is required for a smooth seam.

IMG_1087

Here the other side of the fuselage is shown with the cheek fairing sheeting glued in place. The portion aft of the balsa sheeting will be covered with thin plywood panels after the fuselage has been covered with cloth.

IMG_1088

The side cheek fairing sheeting is now complete. I’ll sheet the gun hump section now that the side cheek fairings are done. But that’s for next time!

Stay tuned.

To see the next installment (part 10,) of the build-along series, click the link: http://www.modelairplanenews.com/blog/2014/07/22/workshop-build-along-sopwith-camel-part-10-sheeting-the-camels-hump/

 To see the previous “Part 8″ posting in the series, click the link: http://www.modelairplanenews.com/blog/2014/06/30/workshop-build-along-sopwith-camel-part-8-tail-surface-attachment/

 

 

 

 

Featured News, Gerry Yarrish, Scale

About the author

Senior Technical Editor About Me: I have a lifelong passion for all things scale, and I love to design, build and fly scale RC airplanes. With 20 plus years as part of the Air Age family of magazines, I love producing Model Airplane News and Electric Flight.

One Response to “Workshop Build-Along — Sopwith Camel Part 9 — Cheek Fairings”

  1. Pomerantz says:

    Cool i’m building the US also triplane one third scale this is nice good luck with it I’ll try to keep track of what you’re doing

Copyright © 2014 Air Age Media. All rights reserved.